I'm attempting to install the dashboard ashtray in a '57 Ford Ranch Wagon that was removed a few years ago by an unknown prior owner and came to me in a large zip-lock bag. I only have two pieces--the inner tray that would hold the cigarette and ashes, and the door/face plate that pulls down to reveal the inner tray. I see how these two pieces clip together to form one unit, but I don't see how the whole unit fits into the dash. There was no attaching hardware in the zip lock back, so either I'm missing some parts, or it's a compression fit in the dash. If anyone can give me a couple pointers on how this is accomplished, it would be much appreciated! Thanks, Ron ...
A while back I discovered there are two different ash trays for 57's...one for Customs and one for Fairlanes, They are very different but they interchange. I have both, I will take a few pics tomorrow.
Lalessi:
Much appreciated. Mine is a '57 Tudor Ranch Wagon, not a Fairlane, in case that makes it easier for you. I'm proceeding slowly because the dash and the face of the ash tray were recently painted and I'm working with a small area that the tray assembly fits into. Thanks for your help. Ron...
Here are the pics. Had to use two posts.
Ok, here is the explanation. The first two are of a Fairlane ashtray. There are three screws on the "frame", one on each side and one at the top. The "frame" mounts from the back. The door and ash holder are a single part and it goes in from the front. The custom is shown below. The bigger of the parts mounts from the rear, it has the door and the frame as a unit. You can see in the first picture where the paint is still the original gray and match it up to the dash picture. There are three screws, one each side, one at the top. The ash holder goes in from the front and is held in place by the three spring clips on the top.
Hope this is clear... If you need to know anything else or clarification, let me know. The ash holders are removable from the front for dumping out the ashes.
Lalessi: Thank you for that great info. My ashtray is the second one. That would be the one for the Custom. When I got the car about a year ago, everything had been removed from the dash, including the ash tray, and tossed into a couple of boxes. The problem with the ashtray install is that I'm not sure I have all the parts. Right now I have exactly what is in your pictures--the ashtray itself that the ashes go into, and the frame with door that the ash tray "snaps into. And just like yours, mine has one hole in the top and two on each side to secure the ashtray mechanism in the dash. Problem is, there is nothing on the inside of the dash that the 3 sheet metal screws would attach to, leaving me to believe I'm missing at least one more piece that attaches on the backside of the dash and accepts the three sheet metal screws. If you can tell by looking at yours whether there is a third piece, and if you could get a couple pictures of it, that would be helpful. If you can't do that, I understand. I don't want you to start tearing your dash up, too. I'll just keep researching it and maybe come across a parts car I can eye ball up close. Thanks again, Ron
Bad news, the dash is stamped that way with the ash tray flange as part of the dash. I have a dash that you can have but the radio opening has been cut out and then there is the shipping issue.
Can you possibly post a couple pictures of that part of the dash? I can then compare it to mine and maybe get a handle on what, if anything, is missing. Thanks, Ron
I wll try to get that posted today, it is in the attic.
Lynn
I just looked at my dash and there does not appear to have been any cutting or modifications going on back there, so I think I'm good to go. I found another picture online of an ashtray like mine and it appears that the unit mounts using just the one sheet metal screw at the top center, and the sides of the ashtray frame are held in place with the tension of the two sheet metal tabs. I'll see if this works when I get back on the project tomorrow. Many thanks for all your help, Lynn! Hope my message reaches you before you ventured into your attic on my behalf. Ron
No problem, I did get the pictures so I'll post them anyway. You can see all three connecting hoes in the second pic. (Had to use two posts again)
2nd pic...
Lynn--Absolutely identical to my dash. The remaining mystery is the diameter of the 3 "connecting" holes you refer to--they are all too large in diameter to accept the sheet metal screws. Seems that there is a third piece that fits behind them that is not in the box of parts I got with the car. Ron
Lynn: I think what I'm missing are the three small clips that fit over these 3 mounting holes and accept a small sheet metal screw. I used to know the name of these clips, but it escapes me right now. Not sure where I can buy these, but I'm pretty sure they are what I need. Ron
Captive nuts for sheet metal. Any good hardware store will have them.
BW
Captive nuts.
Thank you.
Ron
The screws screw into the ashtray "frame", no captive nuts. The "frame" mounts BEHIND the holes in the dash. Look at the first picture I posted again... :003:
Mine didn't want to fit behind the holes in the dash, but slid right into place in front of the holes. But I see your point and will apply a bit more muscle when I'm back in the garage tomorrow to see if it will position in the rear of the dash holes like your does in the picture. Thanks, again. Ron
There is a 57-59 Ford ash tray currently listed on Ebay that seems to have all of the parts. Have a look.
BW
Yeah, saw them.
Thanks, Ron
yep...Lowe's, Home Depot, etc. look in the metal drawers where the screws/bolts, etc. are.
Quote from: Ron on 2016-10-07 17:14
Mine didn't want to fit behind the holes in the dash, but slid right into place in front of the holes. But I see your point and will apply a bit more muscle when I'm back in the garage tomorrow to see if it will position in the rear of the dash holes like your does in the picture. Thanks, again. Ron
It definitely mounts behind the hole. The Custom ashtray had never been removed from the dashboard until I took it off (based on original paint).
Lynn--If it's still off, can you send me a picture of one of the 3 mounting screws? I'll then head out to Lowe's or Osh and see if I can come close to matching them. Thanks, Ron
Looks to be a #6 maybe #8 X 1/2" long. The same screw hold the glove box in... I think.
Lynn: Thank you for that picture, and the ruler measurement behind it, and your description. You just put my project ahead significantly. If you ever need a hand with anything out my way, please let me know. I'll post a picture of the (correctly) installed ashtray next week. You'll probably be happy to know that this is the last time I take on a project that has been deconstructed by someone else with parts dumped into boxes without zip log bags or source notes. Ron...
Ron,
It was my pleasure to help! If you need anything else....