Help, I need to know if this is the correct amount of oil going to the pass side rockers. Spun the pump to about 600 rpm.
Here is a short vid of it. If not allowed please delete and I will find a different way.
Thanks,
Mike
https://www.facebook.com/groups/1957Fords/permalink/2148473595338891/?mibextid=W9rl1R
Only Facebook members can see...so I'm out. Some of the other guys have FB...I do not.
Yeah, the site wont even register the video on my phone☹️. So this may be my only option. I am sure there are other options but I am technically challenged.
Try this link to you tube.
Does not seem to be much oil to me. I would think more than that at 600 rpm. A sick idle was (I believe...been a long time) 550 and automatic was 700.
We need someone else to verify the idle RPM's.
I would think the oil flow should be a bit more.
Is your cam shaft grooved or cross drilled? What is the oil viscosity?
If your drill motor is 600 rpm that is equivalent to 1200 engine rpm.
IDK but to me that doesn't seem like much oil flow. IIRC adjusting the valves at idle often had oil splashing everywhere but I am getting old and CRS. Fifty plus years ago I put several auxiliary oilers on y blocks. It was almost a common thing to find them on y blocks. There were two types: one used a hollow stud that retained the valve cover and the other came in between the valve cover and the head and connected to the end of the rail.
I just read my drill and realized that low speed is 0-400 rpm. So will film another one at a faster speed. Tim built the engine so I will call him this week to verify things and if I need to go any further.
If Tim built that engine, I would think it would be spot on. He does wonderful work.
I showed two vids of the oil to Tim and he suggested rotating the engine while I prime the engine. Then it occurred to me that the cam may be in just the right position to cut off oil to the pass bank. This is my first Y block and I am slightly paranoid about getting enough oil to the rockers. I will have this thing buttoned up in a day if the oil flows correctly prepping to fire her up!
Quote from: 1930artdeco on 2023-06-12 11:19I showed two vids of the oil to Tim and he suggested rotating the engine while I prime the engine. Then it occurred to me that the cam may be in just the right position to cut off oil to the pass bank. This is my first Y block and I am slightly paranoid about getting enough oil to the rockers. I will have this thing buttoned up in a day if the oil flows correctly prepping to fire her up!
Thats why I asked if it had a cross drilled cam. If you can have some help by turning the engine over slowly while you run the drill the holes in the cam and bearing should line up at some point. good luck. :001:
These engines do not require a lot of valve train oil. Have you ever adjusted your valves with engine running? Too much oil will be sucked down intake guides. If you had a good builder it will be fine. Hell early OHV engines didn't even have top engine oiling, they got an occasional squirt with supplied oil can. Some also has an oil soaked pad laid on top of rockers.
I am going to turn the engine over tonight by the starter and use the drill to turn the oil pump at the same time. Hoping this works.
UPDATE: As usual TIm was right and I was paranoid. I spun the engine and the oil pump and the oil return tube blew off and she shot oil all over the solenoid. IT is back on tighter now;) To be fair though this is my first Y block and I was going to make damn sure the rockers all got the right amount of oil! I mean I spent good money on that engine. Anywho, the valve covers are down (until I half to pull them to verify the gap during the engine break in), fan is on, PS is bolted up, and the lower rad hose is now on. Gaskets come on Friday and then I can bolt up the intake, valley pan, and hook the carb up. Getting close now!
Sounds good! Making rapid progress!
So...at the risk of sounding ignorant...who is this "Tim" everyone seems to know about but me?
Quote from: mustang6984 on 2023-06-13 22:31Sounds good! Making rapid progress!
So...at the risk of sounding ignorant...who is this "Tim" everyone seems to know about but me?
Tim McMaster
HHHHHHHHHHHHhhhhhhhhhhhhhhmmmmmmmmmmmmmmm...hate to say this, but never heard of him. Keep in mind I was out of the automotive circles for a LONG time. But...never heard of him. Is he an engine guru in CA?
As far as I am aware it is Tim McMaster, Steve(?) Mummert are in Modesto and L.A. respectively. With Ted Eaton in Texas. Tim has several you tube videos out on working on Y Blocks and his land speed runs with a Y block-all under The Y block guy. Tim is freaking amazing!
Mummert is in Escondido, San Diego area.
John Mummert is in El Cajon which is south of San Diego near the border.
Quote from: cokefirst on 2023-06-14 22:48John Mummert is in El Cajon which is south of San Diego near the border.
I was close :003:
So was I. To me anything south of San Fran is L.A. to me :003: Wherever he is located he makes great stuff and is very helpful!