Part interchange help

[Wirenut]

Can any one tell me if the rear 1/4 glass and frames from a 57 Lincoln Premier will interchange with a 57 Fairlane 63A (2 door no post). The part numbers for the 57 Fairlane are BAC6329944A and the part number for the Lincoln is BY6029944A. They look the same and I am in desperate need for a set so I can complete my car and get it on the road. I am afraid I know the answer but they look identical and I hate to miss out on a set since I have not had any luck on locating a set. I would appreciate any help in this matter from the wise men of 57 Fordsforever...Thanks

[Ford Blue blood]

Have you tried "The Ford Barn"?  They have a bunch over there that has lots of back ground with Fords in general.  There's one guy that has answered nearly every parts number question that has been posted.

[Zapato]

Wow! Did a Google image search and the rear glass looks like it might work. But nothing forward of the door glass looks workable. Be interesting if they do. Is there a glass guy in your area that does old cars and has patterns ? If so he'd be the guy to ask.  Keep us posted.

Have you placed a Wanted ad on this site ? If not do so.

Zap-

[Boss/Cyclone]

According to classicflatglass.com the Lincoln glass is 2 inches taller than the Ford glass, but the same length.

[Boss/Cyclone]

Try these guys, they have a 57 hardtop in there junkyard. 

All American Classics, Inc.
15209 NE Fourth Plain Road
Vancouver, WA 98682
360.254.8850    800.955.4999    FAX 360.253.5986
Hours: Tues-Friday 8:30-5:00  Saturday 8:30-3:30   Closed: Sunday & Monday

[Boss/Cyclone]

Also, there is a guy here in Michigan parting out one.

[RICH MUISE]

Keep us posted, Kerby. I may be in Phoenix next week..can check out the yards there for you if you still need. We may need to cancel our trip because of a looming furlough my wife may get first of Nov. due to government shutdown. #$@**$#! We were planning on leaving Thursday night, but the prospects of our income being cut off got us a little worried to say the least.

[Wirenut]

Thanks for the responses. I do not have a local source for the glass cutting specs. All I know is I would have to take my old glass to use them as templates. The frames look so close and the part number too. I did post a need on the wanted section but no luck. I will try the sources you have suggested. Boss thanks for checking out the measurements, that helps nail it down, Rich and Zapato, and Blue hood Thanks for your help..

[Zapato]

There are several "Salvage Yards" listed in the parts suppliers list. One of them is bound to be able to help you.

Zap-

[RICH MUISE]

I understood you were looking for the glass and frames, is that correct?

[Wirenut]

Yes I am looking for the glass and frames but will take just the frames.. Just an FYI i tried the recommended locations from earlier and no luck. I did post a request on the ford barn. I will see what that turns up. Thanks Rich..

[Frankenstein57]

If I could make a suggestion, put your location in your avatar. Someone might know of a car nearby, but don't chime in because you might be half way across the country
Mark

[Wirenut]

Good idea, Thanks and done..

[hiball3985]

If I could make a suggestion, put your location in your avatar. Someone might know of a car nearby, but don't chime in because you might be half way across the country
Mark

I wish everyone would do that. I also wish it was a requirement when joining.
And no Jeff, Polakaville doesn't count 

[Jeff Norwell]

I wish everyone would do that. I also wish it was a requirement when joining.
And no Jeff, Polakaville doesn't count 

Jim,I am .....crushed.