News:

Check out the newsletters posted at our main club site:  http://57fordsforever.com

Main Menu

***WANTED*** '57 TRUNK LOCK PARTS

Started by CobraJoe, 2020-06-27 16:19

Previous topic - Next topic
Print
Go Down Pages1 2
User actions

CobraJoe

2020-06-27 16:19
I Copied this over from my Quad Headlight thread because I am in dire need of parts:
In my quest to return my rear deck lid into something that resembles stock, I purchased a NOS trunk lock and cylinder:



However, there are a few pieces I need if anyone has them and would like to sell them, please let me know. They are the 4 pieces circled in red below:



Thanks
When I was fourteen years old, I was amazed at how unintelligent my father was. By the time I turned twenty-one, I was astounded at how much he had learned in the last seven years!

'96 Bronco,
'39 Ford Coupe,
'57 Fairlane,
'68 Torino GT
'15 F150,
'17 Escape,

Ecode70D

#1
2020-06-28 21:01
Sorry Joe
     I don't have anything that looks like that in my junque collection. 

Contibob

#2
2020-06-28 22:43
I am not 100% sure, but I think these parts are the same as 57 Thunderbird. "Macs" has them in reproduction.

CobraJoe

#3
2020-06-29 09:48
Thanks Bob, but this is all that Mac's shows:

When I was fourteen years old, I was amazed at how unintelligent my father was. By the time I turned twenty-one, I was astounded at how much he had learned in the last seven years!

'96 Bronco,
'39 Ford Coupe,
'57 Fairlane,
'68 Torino GT
'15 F150,
'17 Escape,

Contibob

#4
2020-06-29 23:54
Look in the 57 Thunderbird section and you will see the parts you need. Like I said I believe the parts you are looking for are the same used on the 57 T'Bird trunk

terry_208

#5
2020-06-30 16:54
I have 3 of the parts, except for the wire (43226) in my Custom's trunk lid.  All I need to do is remove them. Does anyone know what size the required wrench to remove nut, 356164-S?  I don't have crow foot wrenches so need to reach in to remove it.  How have others removed this nut?
Terry

gasman826

#6
2020-06-30 22:16
Crowfoot.  The only way to go.  1-1/4" maybe.  I could confirm tomorrow if no one comes up with a sure answer.

thomasso

#7
2020-07-01 00:19
Just tightened mine a couple of days ago.  Think it was 1".  Got a good enough grip just by going straight in thru the access hole.
57 E Code Black 76B   55 Willys Aero   63 Rivera   99 Lightning  1- XK8 Convs.   05 Vanden Plas  etc.

CobraJoe

#8
2020-07-01 04:54
Thanks guys.
When I was fourteen years old, I was amazed at how unintelligent my father was. By the time I turned twenty-one, I was astounded at how much he had learned in the last seven years!

'96 Bronco,
'39 Ford Coupe,
'57 Fairlane,
'68 Torino GT
'15 F150,
'17 Escape,

RICH MUISE

#9
2020-07-01 08:40
A plummer's basin wrench is what I used.
I can do this, I can do this, I, well, maybe

gasman826

#10
2020-07-01 12:05
I concur...1" crowfoot.

terry_208

#11
2020-07-01 20:31
Thanks for the info, everyone!  It will make things much easier.
Terry

terry_208

#12
2020-07-06 00:51
Still trying to get this assy apart.  I will give it another hour tomorrow and If it hasn't been removed, I'll simply separate the inner and outer panels. 
Terry

CobraJoe

#13
2020-07-06 04:56
Thanks Terry, I am in no rush to do this, so no worries.
When I was fourteen years old, I was amazed at how unintelligent my father was. By the time I turned twenty-one, I was astounded at how much he had learned in the last seven years!

'96 Bronco,
'39 Ford Coupe,
'57 Fairlane,
'68 Torino GT
'15 F150,
'17 Escape,

terry_208

#14
2020-07-12 13:32
Update:  I had tried a basin wrench w/o success.  Obtained a set of crowfoot wrenches and was able to put some torque on the nut.  It made about 3.5 turns and froze. Putting more, read a lot more, torque on the nut got some results.  Not the results I wanted but results non-the-less.  The lock mechanism broke free of the outside emblem.  A couple minutes with the die grinder freed three of the items Joe needs.   
Terry
Print
Go Up Pages1 2
User actions